Quick setup guide for North AmericaInstructions are listed in the following order. Please page down to the one you require
Manhattan DSR-1500
Manhattan Skyline 1000
Scientific Atlanta______________________________________________________
How to program your Manhattan DSR-1500 to ATN
1. Press "Setup" key once, then the down "ch" key once, and "CHANNEL SEARCH" will be highlighted. Then press the "OK" key, and the "Channel Search" box will appear.
2. Press the down "ch" key three times, and the number "1" will be highlighted in the "TP FREQUENCY" box. Now type 11983 in the box.
3. Press the down "ch" key until Symbol Rate (S/R) is highlighted. Type in 05900.
In a second or two a green or yellow bar will appear in the "SIGNAL STRENGTH" box.4. Press the down "ch" key until there are "" marks on each side of the words "START SEARCH". Press the "OK" key once, and a list will appear with "Adventist TV" on it. NOTE the channel number as this is where you will find the program. The word "STORE" will appear. Now press "OK" again. This will store ACN or ATN as it is now called.
______________________________________________________
How to program your Manhattan Skyline 1000 to ATN
1. Press the "MENU" key, then press the right "VOL" key, so that the "INSTALL" box is highlighted.
2. Press the down "ch" key once, and highlight "2. Channel Search." Now press the "OK" key, and the "CHANNEL SEARCH" box will appear.
3. Press the down "ch" key 4 times until "TP Data" is highlighted, then press the "OK" key, and a new box will appear, on the right, with "TP1:3ABN" at the top in yellow.
4. Press the right "Vol" key once, and "TP2:User Defined" will appear in yellow.
5. Press the down "ch" key once, and highlight "Freq." Now type in the number 11983, with the remote control key pad.
6. Press the down "ch" key twice, and highlight "S/R". Now type in 5900. Within a few seconds you should notice two green bars appear by "Signal" and "Quality".
7. Press the down "ch" key 5 times until "STORE" is highlighted in yellow. Press the "OK" key once and the box will disappear.
8. Press the down "ch" key twice and highlight "START". Press the "OK" key once and the receiver will automatically store the new channel.
______________________________________________________
How to program your Scientific Atlanta to ATN
1. Press MENU. The BSR Main Menu will be displayed.
2. Press 2. The Receiver Status Menu will be displayed.
3. Press 3. The Receiver Setup Menu will be displayed.
4. Frequency Mode should read "downlink". If it does not, press left "VOL" key once. Now press up "ch" key 6 times until Frequency Mode is highlighted. Press "Select" until "downlink" is displayed.
5. Press down "ch" key once. Frequency box will be highlighted. Press "Select". This will create an empty box. Type in 1198300. Your final reading must be 11.983.
Press "Select" once.6. Press down "ch" key once. The L.O. Freq #1 should read 10750. If it does not, press "Select" and type in 10750. Press "Select" once.
7. Press down "ch" key 3 times. Polarization should read HOR. If it does not, press "Select" until it does.
8. Press down "ch" key once. FEC should read 2/3. If it does not, press "Select" until it does.
9. Press down "ch" key once. Press "Select" once. Type in 59000. Final reading should be 5.900. Press "Select" once.
10. Press right "Vol" key once to highlight "EXIT". "Signal & Lock" will appear on the menu above "EXIT".
11. Press "Select" once. Another box appears asking to save changes. Press 1.
The following message will be displayed. "Please wait...acquiring network information".
Press BACK to return